This article listed below in relation to Tools You Need to Install a New Bathtub is immensely entertaining. You should investigate for yourself.
Mounting a bathtub isn't exactly brain surgery, but it does require strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently accessible, the project can move quickly; if you need to open a wall to get rid of the old bathtub as well as place the new bathtub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and set in the brand-new one. See to it you have actually certified yourself for the task as well as are comfortable trying it. Instead of working with a service provider to take over a halfway-completed task, it is better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly help you install a brand-new bath tub in your washroom if you have already purchased a new tub and also do not require to change the arrangement of your previous water pipelines.
Your devices and also material list ought to consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. Once the supply pipes have been removed, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in area in between the faucet as well as the sink. Protect the tap in place with the supplier provided backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The previous type must be linked to the tap ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Tub
Using the two wooden boards under its feet, place the tub in the required position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto four tiny points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the spirit level reads degree.
To mount taps, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water system as well as check all joints as well as new pipework for leakages and tighten them if needed. Load the tub as well as likewise inspect the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait up until the bathtub has been used a minimum of once as this will certainly resolve it into its last setting.
Planning for the Installation
To start with, the sustaining frame provided with the bath should be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, leading to complications with wetness and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in use. The sealer can break rather very early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that excerpt was worthwhile. Do you know about another person who is excited by the subject? Take a moment to share it. Thanks so much for your time invested reading it.
Request A Quote